From 9569375c84907d7f61a3cb9bd0fe387dab6be752 Mon Sep 17 00:00:00 2001 From: sagiferi Date: Thu, 21 May 2026 14:14:10 +0200 Subject: [PATCH] mukodik, csak egy ido utan megall az RA tengely, es lassabb is, mint az eredeti --- Config.h | 44 +++++++++++++++++++++++++++----------------- 1 file changed, 27 insertions(+), 17 deletions(-) diff --git a/Config.h b/Config.h index 99a4cc0..48396aa 100755 --- a/Config.h +++ b/Config.h @@ -19,11 +19,17 @@ #define HOST_NAME "OnStep" -#define AXIS1_STEP_PIN 18 // gyári binárisból kinyerve (volt: 14) -#define AXIS1_DIR_PIN 0 // gyári binárisból kinyerve (volt: 12) [GPIO0 must be high at boot] +#define AXIS1_STEP_PIN 18 // RA motor STEP (GPIO0 nem tud gyors STEP-et, ez a helyes) +#define AXIS1_DIR_PIN 0 // RA motor DIR +#define AXIS1_M0_PIN 13 // TMC MS1 (megosztott) +#define AXIS1_M1_PIN 14 // TMC MS2 (megosztott) +#define AXIS1_M2_PIN 5 // TMC2209 UART - KÖZÖS vonal az AXIS2-vel (megosztott busz) -#define AXIS2_STEP_PIN 27 -#define AXIS2_DIR_PIN 26 +#define AXIS2_STEP_PIN 27 // DEC motor STEP +#define AXIS2_DIR_PIN 26 // DEC motor DIR +#define AXIS2_M0_PIN 13 // TMC MS1 (megosztott) +#define AXIS2_M1_PIN 14 // TMC MS2 (megosztott) +#define AXIS2_M2_PIN 5 // TMC2209 UART vonal (szoftver-soros TX) #define SHARED_ENABLE_PIN 25 // Közös láb, ahogy gyárilag tervezték! #define STATUS_LED_PIN 2 @@ -39,7 +45,11 @@ #define SERIAL_C_BAUD_DEFAULT OFF // OFF, n. Baud rate as above. See (src/pinmaps/) for Serial port assignments. Infreq #define SERIAL_D_BAUD_DEFAULT OFF // OFF, n. Baud rate as above. See (src/pinmaps/) for Serial port assignments. Infreq #define SERIAL_E_BAUD_DEFAULT OFF // OFF, n. Baud rate as above. See (src/pinmaps/) for Serial port assignments. Infreq -#define SERIAL_RADIO WIFI_ACCESS_POINT // OFF, Use BLUETOOTH or WIFI_ACCESS_POINT or WIFI_STATION (ESP32 only.) Option +#define SERIAL_RADIO OFF // OFF, Use BLUETOOTH or WIFI_ACCESS_POINT or WIFI_STATION (ESP32 only.) (ideiglenesen OFF a diagnózishoz) Option + +// TMC2209 UART (szoftver-soros, axiseként saját TX vonal az M2 pinen) ------------------------------------------------------------ +#define SERIAL_TMC SoftSerial // szoftver-soros UART a TMC2209 driverekhez +#define SERIAL_TMC_BAUD 115200 // TMC UART baud rate // STATUS --------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Controller#STATUS_LED #define STATUS_LED ON // OFF, Steady illumination if no error, blinks w/error code otherwise. Option @@ -68,7 +78,7 @@ // Typically: A4988, DRV8825, LV8729, S109, TMC2130, TMC5160, TMC2209, etc. // AXIS1 RA/AZM -------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Axes -#define AXIS1_DRIVER_MODEL TMC2209S // OFF, Enter motor driver model (above) in both axes to activate the mount. <-Often +#define AXIS1_DRIVER_MODEL TMC2209 // OFF, Enter motor driver model (above) in both axes to activate the mount. <-Often // If runtime axis settings are enabled changes in the section below will be ignored (disable in SWS or by wiping NV/EEPROM): // \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ @@ -80,18 +90,18 @@ #define AXIS1_LIMIT_SYNC OFF // OFF, n. Where n= 0..90 (degrees.) Allow sync/reset only within this +/-range. Option #define AXIS1_DRIVER_MICROSTEPS 16 // OFF, n. Microstep mode when tracking. <-Req'd -#define AXIS1_DRIVER_MICROSTEPS_GOTO 4 // OFF, n. Microstep mode used during slews. OFF uses _DRIVER_MICROSTEPS. Option +#define AXIS1_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during slews. OFF = nincs futás közbeni UART mód-váltás (közös busz!) Option // for TMC2130, TMC5160, TMC2209, TMC2226 STEP/DIR driver models: #define AXIS1_DRIVER_IHOLD OFF // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option -#define AXIS1_DRIVER_IRUN OFF // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option -#define AXIS1_DRIVER_IGOTO OFF // OFF, n, (mA.) Current during slews. OFF uses IRUN. Option +#define AXIS1_DRIVER_IRUN 1000 // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option +#define AXIS1_DRIVER_IGOTO 1300 // OFF, n, (mA.) Current during slews. OFF uses IRUN. Option // /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ / #define AXIS1_DRIVER_STATUS OFF // OFF, ON, HIGH, or LOW. For driver status info/fault detection. Option -#define AXIS1_DRIVER_DECAY OFF // OFF, Tracking decay mode default override. TMC default is STEALTHCHOP. Infreq -#define AXIS1_DRIVER_DECAY_GOTO OFF // OFF, Decay mode goto default override. TMC default is SPREADCYCLE. Infreq +#define AXIS1_DRIVER_DECAY SPREADCYCLE // azonos tracking/goto decay = nincs UART mód-váltás + van indítónyomaték Infreq +#define AXIS1_DRIVER_DECAY_GOTO SPREADCYCLE // azonos a fentivel Infreq #define AXIS1_POWER_DOWN OFF // OFF, ON Powers off 30sec after movement stops or 10min after last<=1x guide. Infreq @@ -104,7 +114,7 @@ // |HYST(n) Where n=0..1023 (ADU) for +/- Hystersis range. // AXIS2 DEC/ALT ------------------------------------------------------- see https://onstep.groups.io/g/main/wiki/Configuration_Axes -#define AXIS2_DRIVER_MODEL TMC2209S // OFF, Enter motor driver model (above) in both axes to activate the mount. <-Often +#define AXIS2_DRIVER_MODEL TMC2209 // OFF, Enter motor driver model (above) in both axes to activate the mount. <-Often // If runtime axis settings are enabled changes in the section below will be ignored (disable in SWS or by wiping NV/EEPROM): // \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ \/ @@ -116,18 +126,18 @@ #define AXIS2_LIMIT_SYNC OFF // OFF, n. Where n= 0..90 (degrees.) Allow sync/reset only within this +/-range. Option #define AXIS2_DRIVER_MICROSTEPS 16 // OFF, n. Microstep mode when tracking. <-Req'd -#define AXIS2_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during slews. OFF uses _DRIVER_MICROSTEPS. Option +#define AXIS2_DRIVER_MICROSTEPS_GOTO OFF // OFF, n. Microstep mode used during slews. OFF = nincs futás közbeni UART mód-váltás (közös busz!) Option // for TMC2130, TMC5160, TMC2209, TMC2226 STEP/DIR driver models: #define AXIS2_DRIVER_IHOLD OFF // OFF, n, (mA.) Current during standstill. OFF uses IRUN/2.0 Option -#define AXIS2_DRIVER_IRUN OFF // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option -#define AXIS2_DRIVER_IGOTO OFF // OFF, n, (mA.) Current during slews. OFF uses IRUN. Option +#define AXIS2_DRIVER_IRUN 1000 // OFF, n, (mA.) Current during tracking, appropriate for stepper/driver/etc. Option +#define AXIS2_DRIVER_IGOTO 1300 // OFF, n, (mA.) Current during slews. OFF uses IRUN. Option // /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ /\ / #define AXIS2_DRIVER_STATUS OFF // OFF, ON, HIGH, or LOW. Polling for driver status info/fault detection. Option -#define AXIS2_DRIVER_DECAY OFF // OFF, Tracking decay mode default override. TMC default is STEALTHCHOP. Infreq -#define AXIS2_DRIVER_DECAY_GOTO OFF // OFF, Decay mode goto default override. TMC default is SPREADCYCLE. Infreq +#define AXIS2_DRIVER_DECAY SPREADCYCLE // azonos tracking/goto decay = nincs UART mód-váltás + van indítónyomaték Infreq +#define AXIS2_DRIVER_DECAY_GOTO SPREADCYCLE // azonos a fentivel Infreq #define AXIS2_POWER_DOWN OFF // OFF, ON Powers off 30sec after movement stops or 10min after last<=1x guide. Option