pinek dissassemblalas utan
This commit is contained in:
@@ -19,8 +19,8 @@
|
|||||||
|
|
||||||
#define HOST_NAME "OnStep"
|
#define HOST_NAME "OnStep"
|
||||||
|
|
||||||
#define AXIS1_STEP_PIN 14
|
#define AXIS1_STEP_PIN 18 // gyári binárisból kinyerve (volt: 14)
|
||||||
#define AXIS1_DIR_PIN 12
|
#define AXIS1_DIR_PIN 0 // gyári binárisból kinyerve (volt: 12) [GPIO0 must be high at boot]
|
||||||
|
|
||||||
#define AXIS2_STEP_PIN 27
|
#define AXIS2_STEP_PIN 27
|
||||||
#define AXIS2_DIR_PIN 26
|
#define AXIS2_DIR_PIN 26
|
||||||
|
|||||||
+2
-2
@@ -19,14 +19,14 @@
|
|||||||
// Enables additional debugging and/or status messages on the specified SERIAL_DEBUG port (be sure to disable when done!)
|
// Enables additional debugging and/or status messages on the specified SERIAL_DEBUG port (be sure to disable when done!)
|
||||||
// Note: The SERIAL_DEBUG port is often (almost always) attached to the same SERIAL_A port so it cannot be used for normal
|
// Note: The SERIAL_DEBUG port is often (almost always) attached to the same SERIAL_A port so it cannot be used for normal
|
||||||
// LX200 protocol communications. If this is the case set both to the same (faster) baud rate specified below.
|
// LX200 protocol communications. If this is the case set both to the same (faster) baud rate specified below.
|
||||||
#define DEBUG OFF // OFF, Use ON for background error messages only, use VERBOSE for all Infreq
|
#define DEBUG VERBOSE // OFF, Use ON for background error messages only, use VERBOSE for all Infreq
|
||||||
// error and status messages, use CONSOLE for VT100 debug console,
|
// error and status messages, use CONSOLE for VT100 debug console,
|
||||||
// or use PROFILER for VT100 task profiler.
|
// or use PROFILER for VT100 task profiler.
|
||||||
#define DEBUG_AXIS OFF // OFF, n. Where n=1 to 9 as the designated axis for logging activity. Option
|
#define DEBUG_AXIS OFF // OFF, n. Where n=1 to 9 as the designated axis for logging activity. Option
|
||||||
#define DEBUG_CAN OFF // OFF, Use ON to log CAN interface statistics. Option
|
#define DEBUG_CAN OFF // OFF, Use ON to log CAN interface statistics. Option
|
||||||
#define DEBUG_ECHO_COMMANDS OFF // OFF, Use ON or ERRORS_ONLY to log commands to the debug serial port. Option
|
#define DEBUG_ECHO_COMMANDS OFF // OFF, Use ON or ERRORS_ONLY to log commands to the debug serial port. Option
|
||||||
#define SERIAL_DEBUG Serial // Serial, Use any available h/w serial port. Serial1 or Serial2, etc. Option
|
#define SERIAL_DEBUG Serial // Serial, Use any available h/w serial port. Serial1 or Serial2, etc. Option
|
||||||
#define SERIAL_DEBUG_BAUD 230400 // 230400, n. Where n=9600,19200,57600,115200,230400,460800 (common baud rates.) Option
|
#define SERIAL_DEBUG_BAUD 57600 // 230400, n. Where n=9600,19200,57600,115200,230400,460800 (common baud rates.) Option
|
||||||
|
|
||||||
// NON-VOLATILE STORAGE ------------------------------------------------------------------------------------------------------------
|
// NON-VOLATILE STORAGE ------------------------------------------------------------------------------------------------------------
|
||||||
#define NV_WIPE OFF // OFF, Causes the defaults to be written back into NV (FLASH,EEPROM,etc.) Infreq
|
#define NV_WIPE OFF // OFF, Causes the defaults to be written back into NV (FLASH,EEPROM,etc.) Infreq
|
||||||
|
|||||||
Reference in New Issue
Block a user